Next Generation Photoinjectors

Notice ID:

0000329951

Department/Ind. Agency:

ENERGY, DEPARTMENT OF

Sub-tier:

ENERGY, DEPARTMENT OF

Sub Command:

SLAC Natl Accel Lab -DOE Contractor

Office:

SLAC Natl Accel Lab -DOE Contractor

All Dates/Times are:

(utc-07:00) pacific standard time, los angeles, usa

Updated Published Date:

(utc-07:00) pacific standard time, los angeles, usa

Original Published Date:

0000-00-00 00:00:00

Original Response Date:

jul 05, 2022 03:00 pm pdt

Inactive Policy:

manual

Original Inactive Date:

jul 06, 2022

Initiative:

• None***--***

Product Service Code:

ag13 - energy r&d services; energy supply; experimental development

Original Set Aside:

SLAC National Accelerator Laboratory is operated by Stanford University for the Department of Energy. As a management and operating contractor, subcontracts awarded by the Laboratory are not Federal procurements, and are not directly subject to the Federal Acquisition Regulations in 48 CFR. Nonetheless, certain Federal laws, Executive Orders, and regulations may affect our DOE approved purchasing system, as required by statute, regulation, or contract terms and conditions. SLAC has a requirement for a U.S. domestic end item source equivalent to the following products from Few-Cycle: Quantity: 1, Main fiber holder kit few-cycle standard: fiber holder (entrance and exit), fiber protection tube, 2 pcs. KF25 bellows (nominal maximum pressure: 1.5 bar; operation will fail at 2.5-3 bar). The fiber is not included and should be ordered separately. Quantity: 2, KF25 stainless steel tubing (length to be specified, max. 1 m) incl. two adjustable holders. Quantity: 2, 1” vacuum window mount (20mm clear aperture) including KF40-25 adapter and clamp (window not included) Quantity: 2, Uncoated Window Material: fused silica Diameter: 1" Thickness: 3mm Coating (both surfaces): uncoated Quantity: 1, Gas supply system (3/8”OD) including gas inlet, connection to pump, differential pressure – static pressure option, venting option, 4 valves, 1 needle valve. Quantity: 2, Adapter base plate allowing to raise the beam height of the main fiber kit. Optional item, required only if the beam height differs from the 100mm standard beam height of the kit. Optional item required only if the beam height differs form 100mm. Quantity: 1, Standard mounted fiber (ID = 100µm), length < 1m Quantity: 1, High-pressure upgrade I; increases the nominal maximum pressure to 2.5 bar absolute; operation will fail at pressures >6 bar Quantity: 1, One-time reference customer discount 5% on hardware items #1-9 Quantity: 5, 1 day HCF installation and training, exclusive travel expenses Quantity: 1, Travel costs to USA (flat-rate) Quantity: 1, Packaging, shipping and insurance for the USA The award will be made based upon the Lowest Price Technically Acceptable method. Marking of Proprietary/Confidential Information. Offerors shall properly mark and identify with a restrictive legend or information markings on pages of the proposal that contain Proprietary/confidential information. For Offeror to be eligible for a subcontract award with the University and the U.S. Department of Energy (DOE), Offeror shall be registered with the System for Award Management (SAM). Entities may register at no cost directly at the SAM website: https://www.sam.gov. The resulting purchase order shall be performed in accordance with SLAC National Accelerator Laboratory's Terms and Conditions for Fixed Price Commercial Supplies and Services dated December 2016 NOTE: The following documents are attached in this solicitation. Buy American Act Certificate Terms & Conditions for Fixed Price Commercial Supplies and Services, December 2016 General Terms & Conditions, For On Site "Green" Services, Sucontract Rider, March 2021 Please provide quoted price, delivery, technical compliance statement and certification to the attention of Angela Garcia. Payment Terms: Net 30 days Freight terms: FOB Destination Prepaid and Add

2575 Sand Hill Road

Menlo Park , CA 94025

USA

Primary Point of Contacts:

Angela Garcia